Electric properties

A dual inclusion strategy for textile polymers has been investigated to increase elastic energy storage capacity of fibers used in high velocity impact applications. Commercial fibers such as Spectra and Dyneema are made from ultra high molecular weight polyethylene (UHMWPE). Dynamic elastic energy of these fibers is still low therefore limiting their wholesale application without a secondary metallic or ceramic component. The idea in this investigation is to develop methodologies so that the elastic energy of polyethylene based fibers can be increased by several folds. This would allow manufacturing of an all-fabric system for high impact applications. The dual inclusion consists of a polymer phase and a nanoscale inorganic phase to polyethylene. The polymer phase was nylon-6 and the inorganic phase was carbon nanotubes (CNTs). Nylon-6 was blended as a minor phase into UHMWPE and was chosen because of its large fracture strain - almost one order higher than that of UHMWPE. On the other hand, CNTs with their very high strength, modulus, and aspect ratio, contributed to sharing of load and sliding of polymer interfaces as they aligned during extrusion and strain hardening processes. A solution spinning process was developed to produce UHMWPE filaments reinforced with CNTs and nylon-6. The procedure involved dispersing of CNTs into paraffin oil through sonication followed by dissolving polymers into paraffin-CNT solution using a homogenizer. The admixture was fed into a single screw extruder for melt mixing and extrusion through an orifice. The extrudate was rinsed via a hexane bath, stabilized through a heater, and then drawn into a filament winder with controlled stretching. In the next step, the as produced filaments were strain-hardened through repeated loading unloading cycles under tension.

Doped electrically conductive polymers are one of the critical materials that have allowed the current technological revolution. Essentially all of today's applications of doped conductive polymers involve vinyl-related polymers. While the application of conductive polymers is rapidly increasing, there is need for additional materials with different electrical behaviors. The current focus is on studying condensation polymers that contain a metal atom and the possibility of undergoing entire chain delocalization of electrons. The different series of organometallic condensation polymers were synthesized by employing interfacial polycondensation technique and characterization of these products were carried out using standard techniques like light scattering photometer, fourier transform infrared spectroscopy (FTIR), matrix assisted laser desorption ionization time of flight mass spectroscopy (MALDI TOF MS) and nuclear magnetic resonance spectroscopy (NMR). The electrical measurements were carried out employing Genrad 1650-B impedance spectroscopy. Prior studies conducted in this area have led to the pathway of looking at two aspects; first, surveying 60 metal-containing polymers that can undergo entire chain delocalization studying the effect of different substituents on their electrical properties and secondly, doping selected candidates employing iodine. The products derived from 2-nitro-1,4-phenylenediamine and N-methyl-1,4- pheneylenediamines with titanocene dichloride exhibited about 10 3 to 10 5 fold magnitude increases in the electrical conductivity on doping with iodine, moving it near conductive region. This increase is dependent on the concentration of the iodine and is cyclic. The results support the starting premise that selected metal-containing condensation polymers can be doped to increase their electrical conductivity.

Stable and metastable phases of Fe and Al and structural anomalies of Zn and Cd have been studied by epitaxial Bain path (EBP) and minimum path (MNP) first-principles procedures, based on finding equilibrium structures from minimizing the Gibbs free energy G with respect to structure at a given hydrostatic pressure p and temperature T . The main accomplishments are as follows. (1) This dissertation illustrates the effectiveness of the MNP procedure for finding stable and metastable phases of an element by studying four Bravais phases of Fe including body-centered tetragonal (bct), body-centered cubic (bcc), face-centered cubic (fcc) and rhombohedral (rh) phases. The determination of absolute stability using MNP is new; MNP finds all the elastic constants cjj of a given state and the eigenvalues of the elastic constants matrix, which determine the absolute stability of the state.