Nanostructured materials

The effect of Fe substitution on the crystal structure of hydroxyapatite (HAp) is studied by applying simultaneous Rietveld refinements of powder x-ray and neutron diffraction patterns. Fe is one of the trace elements replacing Ca in HAp, which is the major mineral phase in bones and teeth. The morphology and magnetic properties of the Fe-HAp system are also studied by transmission electron microscopy and magnetization measurements. Samples of Ca(5-x)Fex(PO4)3OH with 0< x < 0.3 were prepared. Single phase HAp was identified in x-ray diffraction patterns (XRD) of samples with x < 0.1 inferring that the solubility limits are less than 0.1. Hematite ((Sa(B-Fe2O3) is identified as a secondary phase for higher Fe content. The refined parameters show that Fe is incorporated in the HAp structure by replacing Ca in the two crystallographic sites with a preference at the Ca2 site. This preference explains the small effect of the Fe substitution on the lattice constants of HAp. The overall decrease of the lattice constants is explained by the ionic vi size difference of Ca and Fe. The increasing trend of the a-lattice constant with x in the Fe substituted samples is attributed to a lattice relaxation caused by the substitution of the 4- and 6-fold Fe at the 7- and 9-fold Ca1 and Ca2 sites. This Ca local geometry reduction is indicated by a slight increase of the Ca1-O3 and Ca2-O1 bond lengths. Above the solubility limit x = 0.05, the Fe is partitioned in and out of the HAp structure with increasing nominal Fe content x. The excess Fe is oxidized to hematite. The TEM analysis and magnetic measurements support the results of the simultaneous Rietveld refinements. The TEM images show no significant effect on the morphology and size of the HAp particles upon Fe incorporation. The particles are either spheres or short rods of dimensions 20-60 nm. Hematite particles are imaged in the samples with x exceeding the solubility limit. These particles

SC-15 epoxy is used in many industrial applications and it is well known that the mechanical and viscoelastic properties of epoxy can be signicantly enhanced when reinforced with nanofillers. In this work, SC-15 epoxy is reinforced by loading with magnetically-active nanofillers and cured in a modest magnetic field. Because of the signicant magnetic response of the nanofillers, this is a low cost and relatively easy technique for imposing a strong magnetic anisotropy to the system without the need of a superconducting magnet. It is also found that this method is an effective way of enhancing the mechanical properties of epoxy. Three systems were prepared and studied. The first is a dilute system of various concentrations of Fe2O3 nanoparticles in SC-15 epoxy. The second system is a combination of Fe2O3 nanoparticles and chemically-functionalized single-walled carbon nanotubes (SWCNT(COOH)s) in SC-15 epoxy. The third is a dilute system of SWCNT(COOH)s decorated with Fe3O4 particles t hrough a sonochemical oxidation process in SC-15 epoxy. Samples have an initial cure of 6 hrs in a magnetic led of 10 kOe followed by an additional 24 hours of post curing at room temperature. These are compared to the control samples that do not have initial field curing. Tensile and compressive stress-strain analysis of the prepared systems shows that mechanical properties such as tensile strength, tensile modulus and compressive strength are enhanced with the inclusion of these nanofillers. It is also found that there is an anisotropic enhancement of these properties with respect to the imposed curing field. An interesting phenomenon is observed with the increase in modulus of toughness and fracture strain with nanotube inclusion.

A dual inclusion strategy for textile polymers has been investigated to increase elastic energy storage capacity of fibers used in high velocity impact applications. Commercial fibers such as Spectra and Dyneema are made from ultra high molecular weight polyethylene (UHMWPE). Dynamic elastic energy of these fibers is still low therefore limiting their wholesale application without a secondary metallic or ceramic component. The idea in this investigation is to develop methodologies so that the elastic energy of polyethylene based fibers can be increased by several folds. This would allow manufacturing of an all-fabric system for high impact applications. The dual inclusion consists of a polymer phase and a nanoscale inorganic phase to polyethylene. The polymer phase was nylon-6 and the inorganic phase was carbon nanotubes (CNTs). Nylon-6 was blended as a minor phase into UHMWPE and was chosen because of its large fracture strain - almost one order higher than that of UHMWPE. On the other hand, CNTs with their very high strength, modulus, and aspect ratio, contributed to sharing of load and sliding of polymer interfaces as they aligned during extrusion and strain hardening processes. A solution spinning process was developed to produce UHMWPE filaments reinforced with CNTs and nylon-6. The procedure involved dispersing of CNTs into paraffin oil through sonication followed by dissolving polymers into paraffin-CNT solution using a homogenizer. The admixture was fed into a single screw extruder for melt mixing and extrusion through an orifice. The extrudate was rinsed via a hexane bath, stabilized through a heater, and then drawn into a filament winder with controlled stretching. In the next step, the as produced filaments were strain-hardened through repeated loading unloading cycles under tension.

Natural frequencies of the double and triple-walled carbon nanotubes are determined exactly and approximately for both types. Approximate solutions are found by using Bubnov-Galerkin and Petrov-Galerkin methods. For the first time explicit expressions are obtained for the natural frequencies of double and triple-walled carbon nanotubes for different combinations of boundary conditions. Comparison of the results with recent studies shows that the above methods constitute quick and effective alternative techniques to exact solution for studying the vibration properties of carbon nanotubes. The natural frequencies of the clamped-clamped double-walled carbon nanotubes are obtained; exact solution is provided and compared with the solution reported in the literature. In contrast to earlier investigation, an analytical criterion is derived to establish the behavior of the roots of the characteristic equation. Approximate Bubnov-Galerkin solution is also obtained to compare natural frequencies at the lower end of the spectrum. Simplified version of the Bresse-Timoshenko theory that incorporates the shear deformation and the rotary inertia is proposed for free vibration study of double-walled carbon nanotubes. It is demonstrated that the suggested set yields extremely accurate results for the lower spectrum of double-walled carbon nanotube. The natural frequencies of double-walled carbon nanotubes based on simplified versions of Donnell shell theory are also obtained. The buckling behavior of the double-walled carbon nanotubes under various boundary conditions is studied. First, the case of the simply supported double-walled carbon nanotubes at both ends is considered which is amenable to exact solution.